Connect the positive terminal of the second speaker to the positive terminal of the amplifier. For a parallel connection of two speakers, the resulting impedance is half of the impedance of the speakers assuming the speakers have the same impedance. You have the same two speakers, but the amplifier has a 4 ohm output.

Plug the negative terminal - of the amplifier to the negative terminal of both speakers. The best way is to wire them in series, but make sure that you have a powerful enough amplifier to power them, with an output rating of 16 ohms or more. Not Helpful 5 Helpful 3. How do I add rear surround speakers to my stereo receiver if it only has connections for 2 speakers? A stereo receiver will only play stereo two channels no matter how many speakers you hook up. You have to have a surround sound system to have rear speakers that actually work properly.

Not Helpful 6 Helpful 2. Your amp probably has a line level like a headphone jack sub output, so you can just buy any active subwoofer and plug it in through that. Not Helpful 1 Helpful 0. Can I run speaker wire from my stereo to the amp input if I have no output on the stereo, and then to the speakers from the amp? Answer this question Flag as Strip the other ends and attach to the amp terminals.

You may need to pop the rocker panels open and drill holes to hide the wires along the door frame. If so, use grommets to insulate the wire from the rough metal edges of the holes. Never use an amp that has output wattage greater than your speakers can handle. Video of the Day. Brought to you by Techwalla. Items you will need Flathead and Phillips head screwdrivers Electric drill and bits Wire cutters to gauge speaker wire Wire strippers Duct and electrical tape Plastic ties Rubber grommets, optional. How to Install a Car Amp Google: About the Author Joe Murray began writing professionally in What I realized is a lot of people who come to our store looking for a stereo system may not have the slightest clue how to set one up.

Understandably, they have not had many years of experience connecting stereo equipment on an almost daily basis to learn how to do it themselves. My goal is to walk you through how to hook up a simple stereo system so you can enjoy listening to your favorite music, whether you listen to CDs, MP3s, radio, records, or any combination. Each stereo system is unique and can get way more complicated pretty quickly, depending on your listening requirements. However, a basic setup like this will give you great sound for whatever you listen to. These are your 4 audio cables pictured in front and your 5 speaker wire pictured in back.

See the pictures below for a visual aid! They will walk you through these steps to make it easier to understand. To start, it helps a great deal to draw a picture of what you are connecting. Draw all of your equipment speakers, receiver, and sources and then draw the connections between them. Basically, your sources will connect to the receiver, and then the receiver goes to the speakers.

How to Connect a Stereo System

Set up your equipment where you want it to go. Figure out where you want to put your speakers. How will you run the cables in between everything? Should you put your CD player on top of the receiver to make it easier to reach the disc tray? Do you need to make room for a turntable? Think of how you will use the system the most and what will be most comfortable for you. Connect the audio output from your first source a CD player, for instance to an audio input on your receiver with your cables.

The red cable will plug into the red holes, and the white cable will plug into the white holes. Which audio input do you use on the receiver? Try to match it to the name.

A Step-by-Step Guide to a Simple System

Run your speaker wire from the receiver to your speakers. Look for the speaker terminals red and black and stick the wire in there. Some receivers may have clips that you push down to stick the wire in; others you may have to unscrew a cap to stick the wire in and screw it back down again. Make sure your speaker wires are not too tight as this could cause problems later on.

Give yourself enough slack to connect everything comfortably! Connect the speaker wires from the terminals on the receiver top picture to the inputs on the back of the speakers bottom picture. Here, your CD player is connected on the left side, while your speakers are connected to the terminals on the right side.

Try moving the speakers around to see what positioning gives you the best sound. Use wire ties or zip ties to bundle up your cables, giving you a clean, organized stereo system. Once you do this a few times, you will get the hang of it. I hope this has been educational and has helped you get your stereo system setup and running. If you have any questions about setting up a stereo or want a more in-depth explanation of anything in this article, please comment below. Now this old hippie can rock n roll all night long and party everyday!

I have a floor model stereo from the that my brother gave to me. I want to replace everything on it.

The floor model cabinet is still beautiful! Yes, this article needs to show how to hook up a turntable to a stereo system. I plan to update this in the next few weeks with more instructions and pictures for adding equipment like a turntable. I am having trouble hooking up my stereo system, I have 4 pieces of equipment. Kenwood Stereo Synthesizer tuner KT, 2. Connect the KT tuner to the KC control amplifier.

Make sure you have the antenna hooked up to the tuner. Connect the KC control amplifier to the KM power amplifier. Connect the KM power amplifier to your speakers. As for the SS surround processor, it is unnecessary in this setup. You would need a surround sound amplifier instead of a stereo amplifier to benefit from the surround processor.

Use AirPlay — some stereos support AirPlay and if yours does, you can connect your iPhone wirelessly to your stereo. Use Bluetooth — if your stereo has Bluetooth, you can connect your iPhone wirelessly to your stereo. We also just bought vintage kenwood stereo rack with 5 pcs! Adding turntable, need intructions to even hook the systems together to work.

Can you tell me how to hook up wireless speakers and can you recommend some wireless speakers? As for how to hook up wireless speakers, it would help to know what you are hooking up and what you need it to do. Different wireless speakers work with different things, like computers, phones, CD players, and so on. Some wireless speakers work around the house while others you can take out to your backyard or just about anywhere else. All outputs say record out. What do I hook my speakers to? From the amplifier, you would hook up a speaker cable from the speaker outputs to your speakers.

I would recommend connecting the antenna to the tuner for the best reception. You may need a longer antenna cable. Receivers give off lots of interference and we at Stereo Barn have found this can cause problem with radio reception and remote control systems. To solve this, place your antenna as far as possible from the receiver because it may be interfering with reception.

You may need a new receiver or tuner. You may need an internet-connected radio. For instance, around Reading, PA where Stereo Barn is located, the hills and mountains block a lot of radio stations from coming in over the air. Instead of using a traditional radio tuner, a lot of our customers use an internet-connected device like a Sonos Connect music player to tune into the local radio stations. In addition to tuning in your local stations, you can also tune into nearly any radio station in the country, if not the world.

Most radio stations broadcast over the internet in addition to over the air. The quickest and cheapest option would be option 1 to extend your antenna and see if that helps.

How To Hook Up Car Audio Amplifier For Subs - Basic and Simple Guide

Can wait to listen to my old casettes and horrify my teens! I have a few questions What speaker wires do you recommend? I would recommend getting new speaker wires for your speakers. Over time, the copper oxidizes and turns dark green which degrades the sound quality.

For the best value, I would recommend getting a guage or the bigger guage speaker wire depending on the size of your speakers. The auxiliary cord must have the 3. I am trying to hook my components back up after moving. I have a Kenwood receiver,cd player and equalizer. Any help would be appreciated. From what I understand, you have to have connect a CD player to a stereo unit unless the CD player has speaker outputs right on it.

What do you need to set up a stereo system?

If the CD player has speaker outputs, this means it has an amplifier built in. The amplifier makes your music loud enough to be heard through speakers. So, I recently inherited an old stereo system. I was able to find manuals for how to set up the system control wires and everything else, except for power. However, I have no idea if it is necessary, wise, or even useful to do this. Is there a general rule for how these should be plugged in? Yes, the Kenwood Spectrum supports plugging the units into each other.

This benefits you by turning everything on with one button push instead of multiple pushes. I would think the engineers who designed this system designed it well enough to handle having everything plugged in and drawing power from the same supply. It looks like you can plug two units the CD player and tuner, for example into the KA which then plugs into the KM and finally to your electrical outlet.

How do you connect a subwoofer to an amplifier? | HowStuffWorks

Whether you should hook it up this way is a matter of preference. If it makes the system easier to work, then I say try it and see if you like it. My sister is trying to hook up my Kenwood Home Stereo system up to my TV and there is no sound coming out of it. What is the problem with it and how do i make it work with sound? Is your TV set to output sound to your stereo or the TV speakers?

You will probably find this setting under a section called Audio, Sound, or Speakers. Using this setting will turn off the TV speakers and turn on the audio output for your stereo system. What type of audio cable do you have connecting your TV to your stereo? It could be a red and white RCA cable or an optical cable. Have you tried using different inputs on the stereo? Sometimes using a different input on the stereo can work if some of the other inputs are broken. If you have a CD player or an iPod or something hooked up to a different input that you know works, try hooking up the TV to that input to test it out.

Is a pre-amp needed regardless of the receiver? Can you recommend any pre-amp and receiver, for a begginer like me? Buy a receiver with a phono preamp built-in — this will cost more than adding a preamp to an existing receiver. I recommend either the Integra DTM There are other stereo receivers with phono inputs out there, but I prefer the quality of the Integra and Onkyo lines.

Reply Roland Seal March 7, at 6: First of all may I say that you are doing a great service to people who otherwise would not be able to manage their equipment and enjoy the wonderful music that is available. The phono input on the amp is moving magnet. There was insufficient sound level using that so I have bought a phono amp. I thought that I should plug that into one of the normal input jacks, such as CD instead of the phono input as I was afraid that the amplified signal may be too high and damage the phono input. I now think that this was possibly a mistake since there is a noticeable noise before and after the music on the disc plays.

Thanking you in advance of your reply and if by any chance you are unable to help me please keep on doing the great work you are for others. Thanks for the good guide, but I have trouble connecting the bare wire from my speaker to my Kenwood stereo receiver KR In order to connect the speaker wire to your Kenwood KR stereo receiver, you may need to buy spade connectors.

Video of the Day

You put the open side of the spade connector on the end of each wire and then attach the flat side of the spade connector to the screw terminals on your receiver. The reason I got it was to hook up a few speakers I inherited in our new house, already set up in the back corners of the room, with our TV. I also hooked up a radio antenna, and it works great: The issue I ran into is with output. It may be that I will need to either 1 a new receiver, or 2 a new subwoofer.

But the receiver clearly works fine, and the subwoofer is brand new. I would prefer some other solution. I tried googling and amazon-searching for various cable converters, analog to digital, digital to analog, etc. I think you can set this up so you can use both your receiver and your subwoofer. It is not an ideal setup, but if you need it to work without getting a new receiver or subwoofer it might be the only way. I would try connecting a cable from either the Tape or VCR record outputs into the back of your subwoofer.

I have recently set them up again, however I only get sound out of one speaker. Both speakers work, I have the A channel selected, the speaker cables both work. The balance is in the centre, I have tried different input cables and even different inputs to the amplifier I have been using the CD input as default.

When I have no inputs inserted if I turn up the master volume to full I get the usually hissing from both speakers nothing crackly. The receiver only gets sound from one of the two channels either the left or the right instead of getting both channels like it normally would. Since you hear the hissing noise when you turn up the volume, your receiver can output sound to both speakers. But if it can only get one of two channels from the RCA inputs, it will only output that one channel. To get it fixed, it might be as simple as re-soldering a connection between the inputs and the amp or it could be something more complicated and expensive.

If you want to get it fixed, I would recommend contacting United Radio since they specialize in repairing Sony equipment. You will have to ship it to them and then they give you an estimate for repair if it can be repaired. In total, it could be almost as costly as buying a brand new Sony receiver with a warranty. You might be able to find someone who does repair local to you, but with equipment like surround receivers, parts might be expensive or impossible to get. Hi Nick, first off your setup instructions are great! We are looking to build a new stereo system.

Will Sonos wireless speakers Work with this setup with home wifi or can you recommend one that will? Thank you in advance! The Yamaha R-S receiver works best with traditional wired speakers. The only way I can think of to hook up Sonos wireless speakers like the Play 5, 3, 1, or PlayBar to your stereo is a bit complicated:. I recommend sticking with regular wired speakers for your stereo system and if you want a second system for wireless speakers, go for the Sonos. The Sonos wireless speakers are great for playing music from the internet, but mixing in traditional sources like a CD player or turntable complicates how you have to set your system up and use it.

If there were any good wireless speakers you could directly hook up to a stereo receiver, I would recommend them. I am trying to hook up my sony t. On the back of your TV, look for an audio output. You will either find a red and white analog audio output, an optical audio output, or both.

Next, find an input on the back of your Onkyo receiver. If your receiver has an optical audio input, use that because it will give you the full, digital sound straight from the TV. You will need an optical cable to do this. If not, use the regular red and white analog audio input for your TV. You will need an analog audio cable to do this. Finally, set your receiver to whatever input you used for your TV. Some receivers have a TV input, so use that if you can. Nick, Thanks for your concise and intelligent guide. If you have any suggestions to add to this guide, feel free to let me know. I do not have a system of any kind outside of a Bluetooth speaker that I use for streaming from my phone.

I am going to purchase a record turntable looking at the Audio-technica at-lp60 turntable. I was told that I should buy an older receiver with phono on it and have found some older kenwood and pioneer receivers at a local pawnshop that are reasonable. My question is that I want to listen to the turntable in different rooms then it is in and would prefer to buy a wireless speaker system. Can you connect wireless speakers to an older receiver like that or is the technology not compatible?

Any other way I could accomplish it? To answer your question, yes it is possible to connect speakers wirelessly. You can do this with a wireless receiver and transmitter kit like the Soundcast SurroundCast.


  • How do you connect a subwoofer to an amplifier??
  • my ex is dating someone else what can i do?
  • How to hook up my speakers with an amplifier [Solved] - Home Theatre - Audio.
  • How to Power Two Speakers with a One Channel Amp: 7 Steps.
  • dating calling cards;

The advantage of this setup is you can use your turntable with your stereo receiver and listen with any pair of speakers wirelessly. However, this type of setup will compromise the sound quality and the volume level you can listen at for the convenience of wireless speakers. If you turn the volume level up too high, it could blow the speakers or the wireless receiver. I have an old technics model sa-gx stereo receiver and I used it about a week ago everything was working great, but I recently moved it and tried playing the radio.

The volume on high but it sounded so low. How do I get it where the volume can return to normal install of low? It sounds like one or a few things might be a problem:. I always try swapping out as many parts of the system as possible to see what may be wrong. The easiest thing to try is swap out the speaker wires. Speaker wires can be damaged even if they look fine and this may cause problems with the receiver. Next, try different sources of music like a CD player or iPod. Try your speakers on another stereo receiver. If they sound the same on a different receiver as yours, then the problem may be the speakers.

If the speakers sound noticeably better, the problem may be the receiver. Try taking it back to the store you bought it an see if they can test the receiver on one of their stereo setups. Also, try calling Technics and see if they have any authorized repair centers near you.

And is it the wires or stereo? To figure out where this problem might be, test each individual piece of equipment first the stereo receiver, then the speakers, then the speaker wires, and so on on a second stereo system that you know works. So try playing your stereo receiver on a different set of speakers and wires, then try playing your speakers on a different stereo receiver, etc.

This will narrow down your search to find which piece of equipment is causing the problem. It might be something as simple as replacing the speaker wires. Just like cars, electronics wear out from time and use. Like Ann, I would like to use wireless speakers with my vintage system. Is this possible, can you suggest adapters to do this, as well as wireless speakers that would be appropriate. I do not want to spend a lot of money on this. To play wireless music from your vintage system to speakers, I would recommend the Soundcast Surroundcast: This will let you hook up any small sized speakers to it so you can play music from your sound system to wherever you want your speakers to be.

When I play from my iPhone, only one of the two speakers play and the sound comes out stuffy because the bass plays louder than the normal sound. When I play from my laptop, both speakers play but the same happens, stuffy sound. But when I play radio or music from an USB flash drive it works perfectly. Call the store you got the speakers from, they might know how to help since they sell that brand. Just bought some newish Kenwood speakers off some guy. You need to connect the turntable here because it needs extra amplification compared to the CD and VHS players. Otherwise, you will barely be able to hear the turntable.

In this case, connect a red-and-white audio cable from the audio outputs on the cable box to any red-and-white audio input on the receiver. You need a red-and-white audio cable with a ground connector like this:. You might not need it for this system. Can you tell me where everything goes? And do I need both the amp. Then, connect the speakers to the Sansui stereo. As it is, your Sansui stereo will connect all your inputs and amplify the sound for your speakers. To use your Technics amplifier, you would need a preamplifier to connect all your inputs.

Hello I moved into a house that has the whole house surround system built into ceiling and I just purchased a receiver and had five people yesterday trying to get sound from the speakers. There is Just 3 audio video red white yellow cords coming from the floor and my receiver for audio has spots for the regular speaker wire.

They will best be able to find where the speaker wire goes to and how it hooks up to a surround system. Am not sure in what order to connect the audio RCA jacks to it from dvd player, vcr player, roku 2, cable box and video phone. Tape 1 and Tape 2 record jacks are inputs, but can the playback jacks also be used as inputs?

Have monitor on button for both tapes. From the inputs you describe, you might only be able to hook up 3 devices to this Sansui receiver. The inputs you can use are:. The phono input will only work with a turntable because it has extra amplification meant for a turntable only. If you want more inputs, consider adding an analog audio switcher to your receiver. Do you need two rca cables for each side? Or just one in the amp and on the recording side? But will side A still play? I found a way to connect the red and black speaker wire to a 3. Can I use a jack splitter coming out of tye iPod and plug in one speaker to each hole in the splitter?

Connect a speaker wire to each speaker 2. Connect the speaker wire to the speaker outputs on the amplifier 2. Connect an aux cable from the iPod to a red and white audio input on the amp. Do I use one of the Video connections or Phono or what? The only exception to this would be the Phono input; avoid using that one because it is meant for a turntable only. A set of 3 Bose Accoustimass 7 speakers plus sub woofer came with it - we inherited it all. Two of the Bose speakers have died, so we ordered some more off of ebay. When I initially hooked up one new speaker and compared it to the original, the sound did not seem as clear.

Then I switched them, and the second one was definitely less clear. I then switched back to the first new speaker, and it was fuzzy too! At this point, I am waiting for my husband to re strip the speaker wire which was new in and see if that helps. Can you advise me as to what could cause this fuzzy sound? Also, with the 2 wire speaker wire, does it matter which one goes in which hole black or red? Could this effect speaker performance? The attachment on the Bose speakers has the button you push in, push in the wire and it is attached. Try testing out each individual piece of equipment first the speakers, then receiver, then speaker wires, and so on with a second system that you know works.

So, try the receiver on another set of speakers and speaker wires, or try the speakers on another receiver. Just like a car, electronics will wear out with time and use. As for your question about which hole the red and black speaker wire goes into, yes this could effect the speaker performance. When you connect speakers to your receiver, make sure the wires connect the red to the red ports and black to the black ports.

The Kenwood DC is the controller or preamplifier for your system. This is where everything connects to. There should be a CD player input on the DC One end of my speaker wires are stripped of the coating and the other end is a plug. There are no holes for plugs on either the speaker or the receiver. Do I need to cut off the plug and strip the wires on the offending end? It sounds like you need to cut off the plugs and strip the wire.

Some speaker manufactures cover the plug holes on speakers with red and black plastic caps. This picture shows what they typically look like:. Hello I would appreciate some advice re a problem I have: I just got the whole system out of storage where it has been since when I went overseas for work. The CD input is being used by the CD player. Can I use the Tape inputs?

If so which two of the four can I safely use? I thank you for your time and kind consideration. I have no idea how to wire these, any help would be appreciated, and what else would I need to set them up? I would like to set it up so that it has an auxiliary cord or something similar so I can play music from my phone. I got a pair of Fisher SR speakers from my shop teacher for free as he was going to throw them out. I want to set them up so I can play music from my phone, lIke an auxiliary corder or some thing similar. What else do I need and how would I set them up? Any help will be appreciated.

To listen to music from your phone to your stereo speakers, I would recommend a stereo receiver like the Integra DTM As an alternative to Integra, I would also recommend stereo receivers made by Marantz, Onkyo, Denon, etc. The only other part you would need to play music from your phone to your speakers is an aux cable.